Kunshan WonderTek Technology Co.,Ltd.
 
 
Powerline Ethernet Bridge Phoneline Ethernet Bridge Coaxial Ethernet Bridge BPL power line carrier Smart Grid Industry Wi-Fi/PoE Switch Power carrier isolator&Coupler 4G/5G Router,LTE CPE
Industrial Powerline ethernet bridge with PoE function

Industrial Powerline ethernet bridge with PoE function


WD-G1001M-PoE



 

Introduction

Industrial Powerline Ethernet Bridge WD-G1001M-PoE with PoE function is a kind of equipment using the existing wire transmission network. Can provide 500Mbps transmission rate (TCP/IP)with MIMO power line carrier technology. In a single phase environment through the phase line,null line and ground line three simultaneous transmission; Multiphase environment can be transmitted through 3*Phase lines. Enhanced anti-jamming ability and network transmission performance; At the same time with PoE power supply function. The network cable is directly connected with the network camera supporting PoE power supply or other equipment supporting PoE power supply, so the system construction is more convenient. Adopts 128bit-AES encryption to ensure the security of network communication. WD-G1001M-PoE is an industrial-grade Powerline Ethernet Bridge communication product Which developed by Kunshan Wondertek Technology Co., Ltd. The product adopts ITU-T G.9960 G.hn communication protocol standard and IEEE 802.3AF/ 802.3AT protocol. At present, it has been widely used in intelligent manufacturing, intelligent building, intelligent city street lamp, intelligent electricity meter, solar panel monitoring, communication in dangerous environment, maritime application, automotive application, aerospace application, railway, mineral, intelligent storage, intelligent sorting, automatic garage and other wire or sliding contact line and many other sites.

 

Product features

1000Mbps physical transmission rate and 500Mbps (TCP/IP) transmission rate
Follows the IEEE802.3, 802.3U network standards; ITU-T G.9960 G.Hn, IEEE 802.3AF/IEEE 802.3AT protocols
Provide DC 48V/55V power supply to the network cable of the transmission network
Adopts 128bit-AES encryption to ensure the security of network communication
Wide-voltage input for various low-voltage power environments
Low cost and high efficiency
Packet loss:≤0.1%(100M,load 70%)
Support 7*24 hours of all-weather work
Hardware watchdog function
Low delay communication
NDIM (Near Field Interference)

 

Product technical characteristics        

support G.hn protocol standard.
fixed installation method.
rate adaptive.
802.3D Ethernet Bridge
802.1Q VLAN
Quality of Service(QoS) 
IGMO(IPv4)Snooping&MLD(IPv6)Snooping  
The working temperature  -40℃-85℃l
Operating temperature :10%-85%
non-condensing state Preservation humidity 5%-90% non-condensing
state.
ITU-T G.9960   
IEC 60529  
IEC 50022  
IEC 60068-2-6  


Specification

Interface 1*LAN 10/100/1000Base-TX  self Adaption RJ45 Port (waterproof),MDI/MDX;   1*3 core power interface (waterproof)
Operating voltage range AC150-630V/DC200-890V
LED display Light Ethernet, PLC link ,power ,PoE
Transfer frequency 2-50MHz and MIMO
Protocol ITU-T G.9960 (G.hn) ,IEEE802.3,IEEE802.3x, IEEE802.3u
IEEE802.3af/ IEEE802.3at
Security 128-AES
Transfer rate(PHY) 1000Mbps
Number of each Group 7
Modulation OFDM
Effective transfer rate TCP/IP  500Mbps
Manageability Remote Firmware update,support TR-069(optional)
802.1D Ethernet Bridge
802.1Q VLAN
Quality of Service(QoS)
Operating temperature -40℃-85℃
Weight About 0.50kg
Size 220*160*100(mm) (L×W×H)
Operating environment Operating humidity:10%-85%(no condense)
Storage humidity: 5%-90% (no condense)
Certification FCC、CE class B,WEEE,RoHS
Transmission distance 400m Max
Transmission lines Three-wire transmission MIMO Mode
    

Immunity of ESD

The testing voltage which the device should be beared: ±6kV direct Discharge, ±8kV air discharge; 
Discharge number in Each sensitive testing point: Plus-n-Minus 10 times each;
Every time the discharge interval is 1 s. According to B/T 17626.2-2006.

 

Immunity of electrical fast transient impulse group(Commonmode)

The testing voltage which the device should be beared:
Between the power supply voltage port and ground: ±2.0kV;
Between signal circuit and ground: ±1.0kV;
Repetition frequency: 5KHz;
Test duration: 1 min/ time;
Testing times: Plus-n-Minus 5 times each. According to GB/T 17626.4-2008.

 

Anti interference of surge impact

The testing voltage which the device should be beared: ±2kV;
The interval of continuous impulses: 1min/time;
Test number: Plus-n-Minus 5 times each. According to GB/T 17626.5-2008.(protection: all models protection and varistor series of
discharge tube type)
 

Anti- vibration

Meet the demand of MX3 in TB1433(0-200Hz,2g acceleration, maximum amplitude 7mm), interface with no loose, device with no Sealing off and drop in the test.

 Connection topology




LED display light




Item Status Description
ETH ON Connect the network device successfully
  OFF Connect the network device unsuccessfully
  FLICKING Be connecting the network device
PLC ON Connect the similar device successfully
  OFF Connect the similar device unsuccessfully
  FLICKING Exchanging the data with the similar device
PWR ON The device is power on
  OFF The device is power off
PoE ON PoE Function starts
  OFF PoE Function not enabled


 

 
Share:
Next:None

Contact us

0512-83670078

15962529299
Available Time: 9:00-20:00 GMT+8
Learn more
Copyright © 2018 Kunshan WonderTek Technology Co.,Ltd.         
Tel Map