Kunshan WonderTek Technology Co.,Ltd.
 
 
Powerline Ethernet Bridge Phoneline Ethernet Bridge Coaxial Ethernet Bridge BPL power line carrier Smart Grid Industry Wi-Fi/PoE Switch Power carrier isolator&Coupler 4G/5G Router,LTE CPE
1Gbps Industrial Powerline Ethernet Bridge (T/T4/V3/S/D)

Brief introduction

DIN rail industrial PLC Ethernet bridge is a powerline telecommunication product which developed by WonderTek Technology (KunShan) Co.,LTD., it supports the G.hn protocol and the actual bandwidth up to 400Mbps. The product has been widely used in many aspects just as railway, mines, industrial telecommunication and metro etc...

1.1 Highlight

1.1.1 Technical parameters            

 Support G.hn.
 Industrial DIN rail style installation.
 Actual bandwidth up to 400Mbps.
 The maximum transfer distance up to 1000 meters.
 Self-adapt the rate.
 Compatible with all G.hn devices.
 One Domain Master can manage 15pcs End Point.
 There can be 16 groups(16 different Domain Master) of PLC telecommunication devices in the same power line circuit.

1.1.2 Manageability

 Support Remote Firmware update(TR069).
 802.3D Ethernet Bridge.
 802.1Q VLAN.
 Quality of Service(QoS).
 IGMO(IPv4)Snooping&MLD(IPv6)Snooping.
 Support local web management.

1.1.3Operating environment

 Working temperature:  -40℃-80℃.
 Operating humidity: 10%-85% no condense.
  Storage humidity:5%-90% no condense.

1.1.4 Design standards

 ITU-T G.9960
 IEC 60529
 IEC 50022
 IEC 60068-2-6
 MIL-STD-810G

 

Specification:

Model

WD-1001M-DIN(T/T4/V3/S)   

WD-1001M-DIN(D)

Interface

1*LAN 10/100/1000Base-TX self adaption RJ45,
1*AC power interface MDI/MDX support

1*LAN 10/100/1000Base-TX self adaption RJ45,
1*DC power interface MDI/MDX  support

LED display light

Ethernet, PLC link ,power

Transfer band

25,50 and 100MHz and MIMO (based on G.9963)

Protocol(PHY)

IEEE802.3,IEEE802.3x, IEEE802.3u   G.Hn

Security

128-AES

Transfer rate(PHY)

800Mbps

Modulation

OFDM

Effective transfer rate

TCP/IP  400Mbps   

Manageability

Remote Firmware update,support TR-069(optional)

802.1D Ethernet Bridge

802.1Q VLAN

Quality of Service(QoS)

IGMO(IPv4)Snooping&MLD(IPv6)Snooping

Operating temperature

-40℃-80℃

Size

67*160*123 (mm)(L×W×H)

Weight

0.35kg

0.30kg

Operating environment

Operating humidity:10%-85% (no condense)

Storage humidity: 5%-90%(no condense)

Certification

FCC、CE class B,WEEE,RoHS

 

1.2 Features

(1) Packet loss:≤0.1%(100M,load 70%).
(2) Support 7*24 hours all weather operation.
(3) Hardware watch dog function.
(4) PING≤2MS.
(5) The quantity of the group ≤16pcs.

1.3 Immunity of ESD

The testing voltage which the device should be beared: ±6kV direct Discharge, ±8kV air discharge; 
Discharge number in Each sensitive testing point: Plus-n-Minus 10 times each;
Every time the discharge interval is 1 s.
According to B/T 17626.2-2006.

1.4 Immunity of electrical fast transient impulse group(Common mode)

The testing voltage which the device should be beared:
Between the power supply voltage port and ground: ±2.0kV; 
Between signal circuit and ground: ±1.0kV;
Repetition frequency: 5KHz;
Test duration: 1 min/ time;
Testing times: Plus-n-Minus 5 times each.
According to GB/T 17626.4-2008.

1.5 Anti interference of surge impact

The testing voltage which the device should be beared: ±2kV;
The interval of continuous impulses: 1min/time;
Test number: Plus-n-Minus 5 times each.
According to GB/T 17626.5-2008.(protection: all models protection and varistor series of discharge tube type)

1.6Anti- vibration

Meet the demand of MX3 in TB1433(0-200Hz,2g acceleration,  maximum amplitude 7mm), interface with no loose, device with no Sealing off and drop in the test.

1.7 System topology

WD-1001M-DIN(T)

WD-1001M-DIN(T4)


WD-1001M-DIN(V3)

WD-1001M-DIN(S)

WD-1001M-DIN(D)


 

Product model selection:

Model

Ethernet Port

Line Environment

Network Structure

WD-1001M-DIN-T

1

AC(3 phases+N)

Network access points must be connected in 3 phases, and terminals can be mixed in 3 phases and 1 phase
(85-520V)

WD-1001M-DIN-T4

1

AC(3 phases+N)

Network access points and terminals require uniform standard connections (85-520V)

WD-1001M-DIN-V3

1

AC(3 phases)

Only three phase connection, and according to the unified standard wiring (85-520V)

WD-1001M-DIN-S

1

AC(phase + null + ground) 

Single phase with ground (85-520V)

WD-1001M-DIN-D01

1

DC

9-36V

WD-1001M-DIN-D02

1

DC

18-75V

WD-1001M-DIN-D03

1

DC

100-700V

 

 
Share:

Contact us

0512-83670078

15962529299
Available Time: 9:00-20:00 GMT+8
Learn more
Copyright © 2018 Kunshan WonderTek Technology Co.,Ltd.         
Tel Map